斯米克S111钴基1号堆焊焊丝|RCoCr-A钴基合金焊丝-中国工控网(chinagkong.com)-中国工控行业门户网站

首页 > 供应 > 焊条 >

斯米克S111钴基1号堆焊焊丝|RCoCr-A钴基合金焊丝

来自：天津赫伯特焊材科技有限公司

面议

发布时间：2020-6-2 关注次数：215

产品参数

商品详情

斯米克S111钴基1号堆焊焊丝|RCoCr-A钴基合金焊丝上海斯米克S111钴基1号堆焊焊丝|RCoCr-A钴基合金焊丝
 标准：
相当AWS RCoCr-A
 说明：
S111 是连铸的低碳钴铬钨（司太立）合金堆焊焊丝，是钴铬钨堆焊合金中碳及钨含量最低，韧性最好的一种。因此能够承受在冷热条件下的冲击，而且产生裂纹的可能性也小。堆焊层具有良好的耐蚀、耐热、耐磨性能，在 650℃左右的高温下，亦能保持这些特性。用硬质合金刀具易进行切削加工，金相组织为含钨、铬的钴基固溶体（奥氏体）和固溶体与铬钨复合碳化物共晶。
 用途：
要求在高温工作时能保持良好的耐磨性及耐腐蚀性，例如堆焊高温高压阀门、热剪切刀刃、热锻模等冲击和加热交错地方，可具有良好的性能。
 焊丝化学成分（%）
C Mn Si Cr W Ni Fe Co
0.9~1.4 ≤1.0 0.4~2.0 26.0~32.0 3.0~6.0 ≤3.0 ≤3.0 余量
 堆焊金属常温硬度：
HRC=40~45
以上化学成分及常温硬度指堆焊三层以上堆焊金属。
 供应规格（mm）
焊丝直径Φ 3.2 4.0 5.0 6.0
焊丝长度 350；1000
 注意事项：
1. 用氧- 乙炔碳化焰进行堆焊，焰心与内焰的长度比应保持为1：3。
2. 焊接面的边角部分一定要加工成圆角。并在清除母材表面的氧化物及油等污物后进行堆焊。
3. 应当根据母材的种类和工件大小，选择适当的温度进行预热。
4. 堆焊时，母材只须加热到呈“出汗”（润湿）状态，便可加入焊丝熔滴

Category 类别		Trade-mark 牌号		Specification 规格		Melting Point 熔点(℃)	Chemical composition 主要成份(%)	Application 用途	Equivalent to AWS 相当AWS
		L103斯米克银焊条		Wire & rod 丝		885-888	Cu54 Zn Rem.	Brazing of copper, bronze and steel, subjected to low load. 钎焊铜、青铜和钢等受力不大工件
		L104斯米克银焊条		Foil 箔		890-930	Cu57 Mn2 Co2 Zn Rem.	Brazing of carbide cutting tool. 钎焊硬质合金刀具
		L201斯米克银焊条		Cast rod, wire & rod, powder 铸条、丝、粉		710-800	P7 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-2
		L204斯米克银焊条		Cast rod, wire 铸条、丝		640-815	P5 Ag15 Cu Rem.	Brazing of copper, copper alloys, silver and molybdenum etc. 钎焊铜及铜合金、银、钼等金属。	BCuP-5
		L205斯米克银焊条		Cast rod, wire & rod, powder 铸条、丝、箔		640-800	P6 Ag5 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-3
		L207斯米克银焊条		Cast rod, wire & rod 铸条、丝		640-770	P7 Ag5 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金	BCuP-7
		L209斯米克银焊条		Cast rod, wire 铸条、丝		684-710	P7 Ag2 Cu Rem.	Brazing of copper and copper alloys. 钎焊铜及铜合金。	BCuP-6
		L302斯米克银焊条		Wire & rod 丝		745-775	Ag25 Cu40 Zn Rem.	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
		L303斯米克银焊条		Wire & rod 丝		660-725	Ag45 Cu30 Zn余	Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-5
		L303F斯米克银焊条		Flux coated rod 涂药丝		660-725	Ag45 Cu30 Zn Rem.	L303 coated with flux, the same application as L303. 外涂钎剂的L303，用途与L303相同	BAg-5
		L304斯米克银焊条		Foil 箔		690-775	Ag50 Cu34 Zn Rem.	Brazing of copper, copper alloys and steel etc. 钎焊铜及铜合金、钢等	BAg-6
		L308斯米克银焊条		Wire & rod 丝		779-780	Ag72 Cu Rem.	Brazing of copper and nickel under vacuum or reducing protective atmosphere. 铜和镍的真空或还原保护气氛钎焊	BAg-8
		L312斯米克银焊条		Wire & rod 丝		595-605		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
		L313斯米克银焊条		Wire & rod 丝		625-635		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-1a
		L321斯米克银焊条		Wire & rod 丝		615-650		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-7
		L323 斯米克银焊条		Wire & rod 丝		665-755		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等
		L325 斯米克银焊条		Wire & rod 丝		645-685		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-36
		L326 斯米克银焊条		Wire & rod 丝		650-720		Brazing of copper, copper alloys, steel and stainless steel etc. 钎焊铜及铜合金、钢及不锈钢等	BAg-34
		L400 斯米克银焊条		Cast rod, wire & rod 铸条、丝		577-582	Si11.5 Al Rem.	Brazing of aluminum and aluminum alloys. 铝及铝合金的钎焊	BAlSi-4
		L401斯米克银焊条		Cast rod 铸条		525-535	Si5 Cu28 Al Rem.	Brazing of aluminum and aluminum alloys. 铝及铝合金的钎焊
		L600 斯米克银焊条		Wire & rod 丝		183-185	Sn60 Sb≤0.8 Pb Rem.	Soldering of fusible metals and heat-treated part. 易熔金属及热处理件的钎焊	60Sn
		L601 斯米克银焊条		Wire & rod 丝		183-227	Sn18 Sb2 Pb Rem.	Soldering of copper, copper alloys and galvanized iron plain sheet. 铜及铜合金、镀锌铁皮的钎焊。	18Sn
		L602 斯米克银焊条		Wire & rod 丝		183-256	Sn30 Sb2 Pb Rem.	Soldering of copper, brass, copper alloys and galvanized iron plain sheet. 铜、黄铜、铁、镀锌铁皮的钎焊	30Sn
		L603 斯米克银焊条		Wire & rod 丝		183-235	Sn40 Sb2 Pb Rem.	Soldering of copper, copper alloys, steel and zinc parts. 铜及铜合金、钢、锌制零件的钎焊	40Sn
		L604 斯米克银焊条		Wire & rod 丝		183-222	Sn90 Sb≤0.15 Pb Rem.	Soldering of copper and steel for food and medicine field. 食品、医疗所需铜、钢等金属的钎焊	90Sn
		L605 斯米克银焊条		Wire & rod 丝		232-240	Ag5 Sn95	Soldering of copper and steel for electrical and food field. 电器、食品所需铜、钢等金属的钎焊
		L608 斯米克银焊条		Wire & rod 丝		295-305	Sn5.5 Ag2.5 Pb Rem.	Soldering of copper, copper alloys, steel and stainless steel. 铜及铜合金、钢及不锈钢的钎焊
		L702 斯米克银焊条		Powder 粉		970-1000	Cr7 B3 Si4 Ni Rem.	Brazing of stainless steel under vacuum or protective atmosphere. 不锈钢真空或保护气氛钎焊	BNi-2
	Trade- Mark 牌号		Equivalent to China Standard 相当国标		Characteristics & application 特性和用途					Equivalent to AWS 相当AWS
	D 667斯米克焊条		EDZCr-B-15		HRc≥48. Resistance to wear, gas corrosion and oxidation. Hardfacing of blast furnace hopper and cracker part. HRc≥48，耐磨、耐气蚀、抗氧化。堆焊高炉料钟、破碎机件
	D 802斯米克焊条		EDCoCr-A-03		HRc38-47. Resistance to heat, wear and corrosion. Hardfacing of high temperature part such as the edge of thermo-cutter. HRc38-47，耐热、耐蚀、耐磨。堆焊高温工件如热剪切刀刃					ECoCr-A
	D 812斯米克焊条		EDCoCr-B-03		HRc45-50. Resistance to heat, wear and corrosion. Hardfacing of high temperature part such as internal-combustion engine valve. HRc45-50，耐热、耐蚀、耐磨。堆焊高温工件如内燃机阀					ECoCr-B
	D 822斯米克焊条				HRc≥53. Resistance to Wear and heat, bad shock resistance. Hardfacing of rotating blade wheel of boiler. HRc≥53，耐热、耐磨，但抗冲击性差。堆焊锅炉旋转叶轮
	D 832斯米克焊条		EDCoCr-C-03		HRc≥50. Wear and heat resistance. Hardfacing of high temperature part such as hot-rolling guided way. HRc≥50，耐热、耐磨。堆焊高温工件如热轧导轨					ECoCr-C
	D 842斯米克焊条		EDCoCr-D-03		HRc28-38. Corrosion and thermo-fatigue resistance, work harding. Hardfacing of hot forging die. HRc28-38，耐蚀、抗热疲劳，具有加工硬化性。堆焊热锻模
	Z 308斯米克焊条		EZNi		Pure nickel, excellent general properties. Used to weld thin cast iron part and repair welding machined surface, such as guided way of machine tool. 纯镍，综合性能好。铸铁薄件及加工面补焊用，如机床导卫					ENi-Cl
	Z 408斯米克焊条		EZNiFe		Iron nickel, high strength and excellent ductility. Repair welding of important gray cast iron and nodular cast iron, such as cylinder cap. 镍铁，强度高、塑性好。重要灰铸铁及球铁焊补用，如汽缸盖					ENiFe-Cl
	Z 508斯米克焊条		EZNiCu-1		Copper nickel, good machinability and bad crack resistance. Repair welding of sand hole and gray cast iron machined surface subject to no load. 镍铜，易加工，但抗裂性较差。不受力的灰铸铁加工面及砂眼补焊					ENiCu-B
	Cu 107斯米克焊条		ECu		Red copper, atmosphere and sea water corrosion and excellent electric conductivity. Welding of red copper such as electrical copper row. 紫铜，耐大气，海水腐蚀，导电性好。紫铜焊接用，如导电铜排					ECu
	Cu 207斯米克焊条		ECuSi		Silicon bronze, corrosion resistance and high strength. Welding of copper, silicon bronze and brass. 硅青铜，耐蚀、强度高。铜、硅青铜及黄铜焊接用					ECuSi
	Cu 227斯米克焊条		ECuSnB		Tin phosphor bronze, corrosion resistance and high strength. Welding of copper, silicon bronze and brass. 锡磷青铜，耐蚀、强度高。铜、硅青铜及黄铜焊接用					ECuSn-C
	Cu 237斯米克焊条		ECuAl		Aluminum bronze, wear and corrosion and high strength. Welding or surfacing of copper alloys. 铝青铜，耐磨、耐蚀，强度高。铜合金焊接或堆焊用					ECuAl-A2
	Al 109斯米克焊条		TAl		Pure aluminum, excellent corrosion resistance and middle strength. Welding of pure aluminum. 纯铝，耐蚀性好，但强度不高，纯铝焊接用					E1100
	Al 209斯米克焊条		TAlSi		Silicon aluminum, good crack resistance and wide range of usage. Welding of aluminum alloys other than aluminum magnesium alloys. 铝硅，抗裂性好，通用性大。铝合金焊接用，不宜焊接铝镁合金					E4043
	Al 309斯米克焊条		TAMn		Manganese aluminum, corrosion resistance and high strength. Welding of aluminum alloys. 铝锰，强度高，耐蚀。铝合金焊接用					E3003
	Ni 102斯米克焊条		ENi-1		Pure nickel. Welding and surfacing of nickel and nickel to steel. 纯镍，用于镍、镍与钢的焊接与堆焊					ENi-1
	Ni 207斯米克焊条		ENiCu-7		Copper nickel. Welding and surfacing of copper nickel and copper nickel to steel. 镍铜，用于镍铜、镍铜与钢的焊接与堆焊					ENiCu-7
Category 类别	Trade mark 牌号		Chemical composition 主要成份(%)		Characteristics & application 特性和用途					Equivalent to AWS 相当AWS
Hardfacing 硬面堆焊	S 101斯米克焊丝		C3 Cr28 Ni4 Si3.5 Fe Rem.		HRc48-54. Resistance to wear, gas corrosion and oxidation. Hardfacing of bucket tooth and case pump. HRc48-54，耐磨、耐气蚀、抗氧化。堆焊铲斗齿，泵套
	S 111斯米克焊丝		C1 Cr29 W5 Co Rem.		HRc38-47. Resistance to wear and corrosion at high-temperature. Hardfacing of high temperature and pressure valve. HRc38-47，高温下耐磨、耐蚀。堆焊高温高压阀门					ECoCr-A
	S 112斯米克焊丝		C1.5 Cr29 W8 Co Rem.		HRc45-50. Resistance to wear and corrosion at high-temperature. Hardfacing of valve and hot-rolling pass. HRc45-50，高温下耐磨、耐蚀。堆焊阀门，热轧孔型					ECoCr-B
	S 113斯米克焊丝		C2.5 Cr30 W17 Co Rem.		HRc≥55. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of screw charging carriage. HRc≥55，高温下耐磨、耐热，但抗冲击性差。堆焊螺旋送料机用
	S 114斯米克焊丝		C2.5 Cr30 W12 Co Rem.		HRc≥53. Wear and heat resistance at high temperature, bad shock resistance. Hardfacing of three-cone bit. HRc≥53，高温下耐磨、耐热，但抗冲击较差。堆焊牙轮钻头					ECoCr-C
Copper alloys 铜合金	S 201斯米克焊丝		Sn1 Si0.3Mn0.3 Cu Rem.		Good mechanical properties and crack resistance. Gas welding and argon arc welding of red copper. 机械性能好，抗裂性好。紫铜气焊及氩弧焊用					ERCu
	S 211斯米克焊丝		Si3 Mn1 Cu Rem.		Good mechanical properties. Argon arc welding of copper alloys and MIG brazing of steel. 机械性能好，铜合金氩弧焊及钢的MIG钎焊用					ERCuSi-Al
	S 212斯米克焊丝		Sn5 Cu Rem.		Wear resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨性好。铜合金氩弧焊及钢的堆焊用					ERCuSn-A
	S 213斯米克焊丝		Sn8 Cu Rem.		Wear resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨性好。铜合金氩弧焊及钢的堆焊用					ERCuSn-C
	S 214斯米克焊丝		Al7.5 Cu Rem.		Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用					ERCuAl-A1
	S 215斯米克焊丝		Al9 Cu Rem.		Wear and corrosion resistance. Argon arc welding of copper alloys and surfacing of steel. 耐磨、耐蚀。铜合金氩弧焊及钢的堆焊用					ERCuAl-A2
	S 221斯米克焊丝		Cu60 Sn1 Si0.3 Zn Rem.		Melting point is about 890℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔点约890℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
	S 221F斯米克焊丝		Cu60 Sn1 Si 0.3 Zn Rem.		S221 welding rod coated with flux. 外涂焊剂的S221焊丝
	S 222斯米克焊丝		Cu58Sn0.9Si0.1 Fe0.8 Zn Rem.		Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔点约880℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁					RBCuZn-C
	S 222F斯米克焊丝		Cu58Sn0.9Si0.1 Fe0.8 Zn Rem.		S222 welding rod coated with flux. 外涂焊剂的S222焊丝					RBCuZn-C
	S 223斯米克焊丝		Cu59 Sn0.6 Zn Rem.		Melting point is about 900℃. Braze welding of copper, steel and cast iron. 熔点约900℃。铜、钢、铸铁钎焊用					RBCuZn-A
	S 224斯米克焊丝		Cu62 Si0.5 Zn Rem.		Melting point is about 905℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔点约905℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁
Copper alloys 铜合金	S 225斯米克焊丝		Cu48 Ni10 Zn Rem.		Melting point is about 935℃ and high strength. Braze welding of steel, nickel and carbide alloys. 熔点约935℃。高强度,钎焊钢、镍及硬质合金用					RBCuZn-D
	S 225F斯米克焊丝		Cu48 Ni10 Zn Rem.		S225 welding rod coated with flux. 外涂焊剂的S225焊丝					RBCuZn-D
	S 226斯米克焊丝		Cu60 Sn0.3 Si0.2 Zn Rem.		Melting point is about 900℃. Gas welding of brass, also braze welding of copper, steel and cast iron. 熔点约900℃。黄铜气焊用，也可钎焊铜、钢、铸铁
	S 227斯米克焊丝		Cu58Sn0.9Ni0.5 Si0.1 Fe0.8 Zn Rem.		Melting point is about 880℃. Gas welding and carbon arc welding of brass, also braze welding of copper, steel and cast iron. 熔点880℃。黄铜气焊及碳弧焊用，也可钎焊铜、钢、铸铁					RBCuZn-B
	S 229斯米克焊丝		Cu55 Ni6 Mn4 Zn余		Melting point is about 920℃, high strength. Braze welding of steel, nickel and hard carbide. 熔点约920℃。高强度,钎焊钢、镍及硬质合金用
Aluminum alloys 铝合金	S 301斯米克焊丝		Al≥99.5		Good ductility and corrosion resistance. Gas welding and argon arc welding of pure aluminum. 塑性好、耐蚀。纯铝气焊、氩弧焊用					ER1100
	S 311斯米克焊丝		Si5 Al Rem.		Corrosion resistance, wide range of usage. Gas welding and argon arc welding of aluminum alloys other than high magnesium alloys. 抗裂性好，通用性大。铝合金气焊、氩弧焊用。不宜用高镁合金					ER4043
	S 321斯米克焊丝		Mn1.3 Al Rem.		Good corrosion resistance, weldability and ductility. Gas welding and argon arc welding of aluminum alloys. 良好的耐蚀性、可焊性及塑性。铝合金气焊、氩弧焊用
	S 331斯米克焊丝		Mg5 Mn0.4 Al Rem.		Corrosion resistance and high strength. Argon arc welding of aluminum alloys. 耐蚀，强度高。铝合金氩弧焊用					ER5183