产品分类及特点
Product classification and characteristics
按型号可分为：CB型橡胶止水带（埋入式中间有孔型）；CP型橡胶止水带（埋入式中间无孔型）；EB型橡胶止水带（外贴式中间有孔型）；EP型橡胶止水带（外贴式中间无孔型）。
According to the type, it can be divided into: CB type rubber water stop (embedded intermediate pass), CP type rubber water stop (buried intermediate no pass), EB type rubber water stop (externally attached middle pass), EP type rubber water stop (externally attached middle pass).
按材质可分为：天然橡胶止水带，氯丁橡胶止水带，三元乙丙橡胶止水带。
According to the material, it can be divided into natural rubber water stop belt, chloroprene rubber water stop belt, three ethylene propylene rubber water stop belt.
按使用情况可分为：中埋式橡胶止水带和背贴式橡胶止水带(外贴式橡胶止水带)、钢边橡胶止水带、遇水膨胀橡胶止水带、平板式止水带
According to the usage, it can be divided into: the buried rubber water stop and the back type rubber water stop (externally attached rubber water stop), the steel side rubber water stop, the water swelling rubber water stop and the flat type waterstop.
橡胶止水带主要用于混凝土现浇时设在施工缝及变形缝内与混凝土结构成为一体的基础工程，如地下设施、隧道涵洞、输水渡槽、拦水坝、贮液构筑物等。
The rubber sealing belt is mainly used for cast-in-place concrete when in construction joints and deformation joints and concrete structure has become one of the basic engineering facilities, such as underground tunnels, culverts, dams, aqueducts, liquid storage structures etc..
橡胶止水带是用来进行止水的;钢边橡胶止水带在橡胶中间焊止水片外面近模板处焊定位片,对于钢边橡胶止水带要求满焊,定位片只要牢固就可以了,定位片距模板要有一到二公分的距离,这之间加塑料或者木质垫片。拆模后剔出,割掉螺杆后用微膨胀砂浆填平。还有种国内少见 就是用短一点的螺杆外加连接螺杆,拆模后可以很方便的拆下。
The rubber sealing strip is used for sealing; steel edged rubber water stop outside the middle rubber waterstop welding near the template at the welding positioning piece, the steel edged rubber water stop full welding requirements, as long as the firm positioning piece can, positioning distance template to one to two cm distance, plastic or wooden pads plus this. After stripping out, cut off after the mortar filled with micro expansion screw. There are kinds of domestic rare connection screw rod is a little shorter, after stripping can be easily disassembled.
橡胶止水带是在混凝土浇注过程中部分或全部浇注埋进混凝土中。在浇埋混凝土以前先要使其在界面部位保持平展，接头部分粘接紧固，再以适当的力充分浇捣，震荡混凝土来定位止水带，使其与混凝土良好的结合，以免影响止水效果。
The rubber water stop belt is partially or completely poured into the concrete during the concrete pouring process. Before pouring the concrete, it is necessary to keep it at the interface part. The joints are fastened and fastened. Then the concrete is fully poured and tamper with the appropriate force. The concrete is positioned by the shock concrete to make the water stop band well combined with the concrete so as not to affect the sealing effect.