GVZ圆形板式橡胶支座厂家

橡胶垫块是由多层橡胶片硫化粘合而成一种普通橡胶支座产品,这种产品具有足够的竖向刚度,能够将支座上部构造的反力可靠的传递给墩台,支座具有良好的弹性,以应对桥梁的梁端的转动;又有较大的剪切变形能力，以满足上部构造的水平位移。
The rubber pad is composed of multilayer rubber vulcanization bonding a common rubber bearing products, this product has enough vertical stiffness, can force reliable transfer to the pier upper bearing structure, bearing has good flexibility, rotating beam end in response to the bridge; and a larger shear deformation capacity in order to meet, the horizontal displacement of superstructure.
橡胶垫块的布置
The arrangement of rubber padding blocks
橡胶垫块的布置主要和桥梁的结构形式有关。通常在布置支座时需要考虑以下的基本原则:
The layout of the rubber pad is mainly related to the structural form of the bridge. The following basic principles should usually be taken into consideration in the arrangement of support:
(1)上部结构是空间结构时，橡胶垫块应能同时适应桥梁顺桥向(X方向)和横桥向(Y方向)的变形;
(1) when the superstructure is a spatial structure, the rubber pad should be able to adapt to the deformation of the bridge direction (X direction) and the transverse bridge (Y direction).

GVZ圆形板式橡胶支座厂家
(2)橡胶垫块必须能可靠的传递垂直和水平反力;
(2) the rubber pad must be able to reliably transfer the vertical and horizontal forces.
(3)橡胶垫块应使由于梁体变形所产生的纵向位移、横向位移和纵、恒向转角应尽可能不受约束;
(3) the rubber block should make the longitudinal displacement, the lateral displacement and the longitudinal and constant angle due to the deformation of the beam body as far as possible.
(4)当桥梁位于平坡上，固定橡胶垫块宜设在主要行车方向的前端桥台上;
(4) when the bridge is located on the flat slope, the fixed rubber pad should be located on the front end abutment of the main driving direction.
(5)橡胶垫块宜设置在具有较大垫块反力的地方;
(5) the rubber pad should be set in a place with large counterforce.
(6)在同一桥墩上的几个橡胶垫块应具有相近的转动刚度;
(6) several rubber padding blocks on the same pier should have similar rotational stiffness.
总之，桥梁橡胶垫块的布置原则是既要便于传递支座反力，又要使橡胶垫块能充分适应梁体的自由变形。
In a word, the arrangement principle of bridge rubber pad is not only to transfer the support back force, but also to make the rubber pad fully adapt to the free deformation of the beam.

GVZ圆形板式橡胶支座厂家
橡胶垫块的安装
The installation of rubber pad
(1)在垫块安装之前应对支座的安装位置进行测量检验，支座安装平面应和支座的滑动平面或滚动平面平行，其平行度的偏差不宜超过2‰。
(1) the installation location of the bearing should be measured and checked before installing the cushion block. The bearing installation plane should be parallel to the sliding plane or rolling plane of the bearing, and the deviation of parallelism should not exceed 2 per thousand.
(2)垫块安装前应对活动支座顶、底板的相对位置进行检查。
(2) before the pad is installed, the relative position of the top and floor of the movable support should be checked.
(3)垫块安装后，滚动和滑动平面应水平，其与理论平面的斜度不大于2‰。支座上、下板中心应对中，其偏差不大于2‰。
(3) after the block is installed, the rolling and sliding plane should be horizontal, and the slope of the plane is not more than 2 per thousand with the theoretical plane. The deviation of the upper and lower plate centers is not more than 2 per thousand.
(4)为保证垫块安装平整，一般应在支座底面与职称垫石顶面之间，捣筑20~50mm厚的干硬性无收缩砂浆垫层。
(4) in order to ensure the smooth installation of the pad, the dry and hard shrinkage mortar cushion of 20~50mm thick should be rammed between the bottom of the support and the top of the title stone.
1.面板坝GB柔性填料是专门为混凝土面板、堆石坝周边缝和伸缩缝止水而开发的新型止水材料。
The GB flexible packing of the 1. panel dam is a new type of water stop material developed specially for the concrete face, the surrounding joints of the rockfill dam and the expansion joint.
2.产品特点：面板坝GB柔性填料具有优良的高塑性、耐热性、耐寒性、耐老化性，还具有操作简便、无毒无味、耐水、粘附性能好等特点，且施工投入的人员相对较少，便于加工成型，施工工艺简单，造价低廉
2. features: dam GB flexible filler has good plasticity, high heat resistance, cold resistance, aging resistance, but also has the characteristics of simple operation, non-toxic and tasteless, water resistance, good adhesion, and the construction investment staff is relatively small, easy processing, simple construction process, low cost