西门子24 V/10 A 调节电源6EP1334-2BA20现货-中国工控网(chinagkong.com)-中国工控行业门户网站

首页 > 供应 > PLC控制系统 >

西门子24 V/10 A 调节电源6EP1334-2BA20现货

来自：西工电气技术（上海）有限公司

面议

发布时间：2018-1-2 关注次数：340

产品参数

商品详情

西门子24 V/10 A 调节电源6EP1334-2BA20现货西门子24 V/10 A 调节电源6EP1334-2BA20现货

西门子工业产品采购热线：15618032370 QQ：282119341

西门子产品信息：SITOP PSU100S 24 V/10 A 调节电源输入：AC 120/230 V 输出：DC 24 V/10 A

6EP1336-3BA10

SITOP PSU8200 20A 调节电源输入：AC 120-230 V DC 110-220 V 输出：DC 24 V/20 A

6EP1334-3BA10

SITOP PSU200M 10 A 调节电源输入：AC 120/230-500 V 输出：DC 24 V/10 A

6EP1332-4BA00

SIMATIC PM 1507 24 V/3 A 调节电源用于 SIMATIC S7-1500 输入：AC 120/230 V 输出：DC 24 V/3 A

6ES7307-1EA01-0AA0

SIMATIC S7-300 调节电源 PS307 输入：AC 120/230 V 输出：DC 24 V/5 A

6EP1333-2BA20

SITOP PSU100S 24 V/5 A 调节电源输入：AC 120/230 V 输出：DC 24 V/5 A

产品信息：

概述

单相 SITOP smart 是通用型和功能强大的标准电源，适用于工厂机器设备。虽然结构十分紧凑，但它们具有优异的过载响应：由于功率提升 150 %，可毫无问题地连接较高功耗的负载；120% 的固定过载能力为扩展提供了功率储备。这些电源具有高能效，能耗低，在控制柜内的散热量很小。

要进一步提高 24 V 电源的可用性，可将 SITOP smart 电源与缓冲、DC UPS、冗余和选择性模块结合使用。

主要产品亮点

单相，24 V DC/2.5 A、5 A、10 A 和 20 A
输入电压 120 V 和 230 V AC，自动范围切换
设计紧凑 – 无需留出侧面间隙
具有额定电流的 1.5 倍的额外电源 (5 s/min)，允许短暂的功能过载
在高达 45 °C 环境温度下具有 1.2 倍额定电流的永久性过载能力
可调输出电压用来补偿电压降
信号触点可方便地集成到工厂监视系统中
温度范围宽：-25 或 0 至 +70 °C
通过全面认证，如 cULus、cCSAus、ATEX、IECEx 和 GL

技术规范

Article number	6EP1332-2BA20	6EP1333-2BA20	6EP1334-2BA20	6EP1336-2BA10
Product	SITOP PSU100S	SITOP PSU100S	SITOP PSU100S	SITOP PSU100S
Power supply, type	24 V/2.5 A	24 V/5 A	24 V/10 A	24 V/20 A
Input
Input	1-phase AC	1-phase AC	1-phase AC	1-phase AC
Supply voltage
● 1 at AC Rated value	120 V	120 V	120 V	120 V
● 2 at AC Rated value	230 V	230 V	230 V	230 V
● Note	Automatic range selection	Automatic range selection	Automatic range selection	Automatic range selection
Input voltage
● 1 at AC	85 ... 132 V	85 ... 132 V	85 ... 132 V	85 ... 132 V
● 2 at AC	170 ... 264 V	170 ... 264 V	170 ... 264 V	176 ... 264 V
Wide-range input	No	No	No	No
Overvoltage resistance	2.3 × Vin rated, 1.3 ms	2.3 × Vin rated, 1.3 ms	2.3 × Vin rated, 1.3 ms	2.3 × Vin rated, 1.3 ms
Mains buffering at Iout rated, min.	20 ms; at Vin = 93/187 V	20 ms; at Vin = 93/187 V	20 ms; at Vin = 93/187 V	20 ms; at Vin = 120/230 V
Rated line frequency 1	50 Hz	50 Hz	50 Hz	50 Hz
Rated line frequency 2	60 Hz	60 Hz	60 Hz	60 Hz
Rated line range	47 ... 63 Hz	47 ... 63 Hz	47 ... 63 Hz	47 ... 63 Hz
Input current
● at rated input voltage 120 V	1.25 A	2.34 A	4.49 A	7.5 A
● at rated input voltage 230 V	0.74 A	1.36 A	1.91 A	3.5 A
Switch-on current limiting (+25 °C), max.	33 A	40 A	60 A	11 A
I²t, max.	0.4 A²·s	1 A²·s	5.6 A²·s	10 A²·s
Built-in incoming fuse	T 3,15 A/250 V (not accessible)	T 3,15 A/250 V (not accessible)	T 6.3 A/250 V (not accessible)	T 10 A (not accessible)
Protection in the mains power input (IEC 898)	Recommended miniature circuit breaker: from 3 A characteristic C	Recommended miniature circuit breaker: from 6 A characteristic C	Recommended miniature circuit breaker: from 10 A characteristic C	Recommended miniature circuit breaker: from 10 A characteristic C or circuit-breaker 3RV2411-1JA10 (120 V) or 3RV2411-1FA10 (230 V)
Output
Output	Controlled, isolated DC voltage	Controlled, isolated DC voltage	Controlled, isolated DC voltage	Controlled, isolated DC voltage
Rated voltage Vout DC	24 V	24 V	24 V	24 V
Total tolerance, static ±	3 %	3 %	3 %	3 %
Static mains compensation, approx.	0.1 %	0.1 %	0.1 %	0.5 %
Static load balancing, approx.	1 %	1 %	1 %	1 %
Residual ripple peak-peak, max.	150 mV	150 mV	150 mV	150 mV
Residual ripple peak-peak, typ.	30 mV	30 mV	20 mV
Spikes peak-peak, max. (bandwidth: 20 MHz)	240 mV	240 mV	240 mV	240 mV
Spikes peak-peak, typ. (bandwidth: 20 MHz)	70 mV	140 mV	160 mV
Adjustment range	22.8 ... 28 V	22.8 ... 28 V	22.8 ... 28 V	24 ... 28 V
Product function Output voltage adjustable	Yes	Yes	Yes	Yes
Output voltage setting	via potentiometer	via potentiometer	via potentiometer	via potentiometer; max. 480 W
Status display	Green LED for 24 V OK	Green LED for 24 V OK	Green LED for 24 V OK	Green LED for 24 V OK
Signaling	Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK"	Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK"	Relay contact (NO contact, rating 60 V DC/ 0.3 A) for "24 V OK"	Relay contact (NO contact, rating 50 V DC/ 0.3 A) for "24 V OK"
On/off behavior	Overshoot of Vout < 3 %	Overshoot of Vout < 3 %	Overshoot of Vout < 3 %	No overshoot of Vout (soft start)
Startup delay, max.	0.3 s	0.3 s	0.3 s	1.5 s
Voltage rise, typ.	15 ms	15 ms	20 ms	50 ms
Voltage increase time of the output voltage maximum				500 ms
Rated current value Iout rated	2.5 A	5 A	10 A	20 A
Current range	0 ... 3 A	0 ... 6 A	0 ... 12 A	0 ... 20 A
● Note	3 A up to +45°C; +60 ... +70 °C: Derating 3%/K	6 A up to +45°C; +60 ... +70 °C: Derating 1.6%/K	12 A up to +45°C; +60 ... +70 °C: Derating 3%/K	24 A up to +45°C; +60 ... +70 °C: Derating 5%/K
Supplied active power typical	60 W	144 W	288 W	480 W
Short-term overload current
● on short-circuiting during the start-up typical	9 A	18 A	32 A	35 A
● at short-circuit during operation typical	9 A	18 A	32 A	35 A
Duration of overloading capability for excess current
● on short-circuiting during the start-up	100 ms	800 ms	1 000 ms	100 ms
● at short-circuit during operation	800 ms	800 ms	1 000 ms	100 ms
Parallel switching for enhanced performance	Yes	Yes	Yes	Yes
Numbers of parallel switchable units for enhanced performance	2	2	2	2
Efficiency
Efficiency at Vout rated, Iout rated, approx.	85 %	88 %	90 %	90 %
Power loss at Vout rated, Iout rated, approx.	10 W	16 W	25 W	53 W
Closed-loop control
Dynamic mains compensation (Vin rated ±15 %), max.	0.3 %	0.3 %	0.3 %	1 %
Dynamic load smoothing (Iout: 50/100/50 %), Uout ± typ.				3 %
Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ.	5 %	3 %	3 %
Load step setting time 10 to 90%, typ.	1 ms	1 ms	1 ms
Load step setting time 90 to 10%, typ.	1 ms	1 ms	1 ms
Setting time maximum				10 ms
Protection and monitoring
Output overvoltage protection	protection against overvoltage in case of internal fault Vout < 33 V	protection against overvoltage in case of internal fault Vout < 33 V	protection against overvoltage in case of internal fault Vout < 33 V	Yes, according to EN 60950-1
Current limitation	3 ... 3.4 A	6 ... 7.1 A	12 ... 14.6 A
Current limitation, typ.				21 A
Property of the output Short-circuit proof	Yes	Yes	Yes	Yes
Short-circuit protection	Constant current characteristic	Constant current characteristic	Constant current characteristic	Electronic shutdown, automatic restart
Enduring short circuit current RMS value
● maximum				7 A
● typical	3.4 A	7.1 A	14.6 A
Overcurrent overload capability in normal operation	overload capability 150 % Iout rated up to 5 s/min	overload capability 150 % Iout rated up to 5 s/min	overload capability 150 % Iout rated up to 5 s/min	overload capability 150 % Iout rated up to 5 s/min
Overload/short-circuit indicator	-	-	-	-
Safety
Primary/secondary isolation	Yes	Yes	Yes	Yes
Galvanic isolation	Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178	Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178	Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178	Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178
Protection class	Class I	Class I	Class I	Class I
Leakage current
● maximum	3.5 mA	3.5 mA	3.5 mA	3.5 mA
● typical	0.4 mA	0.4 mA	0.8 mA	1 mA
CE mark	Yes	Yes	Yes	Yes
UL/cUL (CSA) approval	cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259, cCSAus (CSA C22.2 No. 60950-1, UL 60950-1, UL 1604)	cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259, cCSAus (CSA C22.2 No. 60950-1, UL 60950-1, UL 1604)	cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259, cCSAus (CSA C22.2 No. 60950-1, UL 60950-1, UL 1604)	cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cCSAus (CSA C22.2 No. 60950-1, UL 60950-1)
Explosion protection	IECEx Ex nA nC IIC T4 Gc; ATEX (EX) II 3G Ex nA nC IIC T4 Gc; cCSAus (CSA C22.2 No. 213-M1987, ANSI/ISA-12.12.01-2007) Class I, Div. 2, Group ABCD, T4	IECEx Ex nA nC IIC T4 Gc; ATEX (EX) II 3G Ex nA nC IIC T4 Gc; cCSAus (CSA C22.2 No. 213-M1987, ANSI/ISA-12.12.01-2007) Class I, Div. 2, Group ABCD, T4	IECEx Ex nA nC IIC T4 Gc; ATEX (EX) II 3G Ex nA nC IIC T4 Gc; cCSAus (CSA C22.2 No. 213-M1987, ANSI/ISA-12.12.01-2007) Class I, Div. 2, Group ABCD, T4	IECEx Ex nA nC IIC T4 Gc; ATEX (EX) II 3G Ex nA nC IIC T4 Gc; cCSAus (CSA C22.2 No. 213, ANSI/ISA-12.12.01) Class I, Div. 2, Group ABCD, T4
FM approval	-	-	-	-
CB approval	Yes	Yes	Yes	Yes
Marine approval	GL, BV	GL, BV	GL, BV	GL
Degree of protection (EN 60529)	IP20	IP20	IP20	IP20
EMC
Emitted interference	EN 55022 Class B	EN 55022 Class B	EN 55022 Class B	EN 55022 Class B
Supply harmonics limitation	not applicable	EN 61000-3-2	EN 61000-3-2	EN 61000-3-2
Noise immunity	EN 61000-6-2	EN 61000-6-2	EN 61000-6-2	EN 61000-6-2
Operating data
Ambient temperature
● during operation	-25 ... +70 °C	-25 ... +70 °C	-25 ... +70 °C	0 ... 70 °C
— Note	with natural convection	with natural convection	with natural convection	with natural convection
● during transport	-40 ... +85 °C	-40 ... +85 °C	-40 ... +85 °C	-40 ... +85 °C
● during storage	-40 ... +85 °C	-40 ... +85 °C	-40 ... +85 °C	-40 ... +85 °C
Humidity class according to EN 60721	Climate class 3K3, no condensation	Climate class 3K3, no condensation	Climate class 3K3, no condensation	Climate class 3K3, no condensation
Mechanics
Connection technology	screw-type terminals	screw-type terminals	screw-type terminals	screw-type terminals
Connections
● Supply input	L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm² single-core/finely stranded	L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm² single-core/finely stranded	L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm² single-core/finely stranded	L1, N, PE: 1 screw terminal each for 0.2 ... 4 mm² single-core/finely stranded
● Output	+, -: 2 screw terminals each for 0.5 ... 2.5 mm²	+, -: 2 screw terminals each for 0.5 ... 2.5 mm²	+, -: 2 screw terminals each for 0.5 ... 2.5 mm²	+, -: 2 screw terminals each for 0.2 ... 4 mm²
● Auxiliary	Alarm signals: 2 screw terminals for 0.5 ... 2.5 mm²	Alarm signals: 2 screw terminals for 0.5 ... 2.5 mm²	Alarm signals: 2 screw terminals for 0.5 ... 2.5 mm²	13, 14 (alarm signal): 1 screw terminal each for 0.14 ... 1.5 mm²
Connections signaling contact	2 screw terminals for 0.5 ... 2.5 mm²	2 screw terminals for 0.5 ... 2.5 mm²	2 screw terminals for 0.5 ... 2.5 mm²
Width of the enclosure	32.5 mm	50 mm	70 mm	115 mm
Height of the enclosure	125 mm	125 mm	125 mm	145 mm
Depth of the enclosure	120 mm	120 mm	120 mm	150 mm
Required spacing
● top	50 mm	50 mm	50 mm	50 mm
● bottom	50 mm	50 mm	50 mm	50 mm
● left	0 mm	0 mm	0 mm	0 mm
● right	0 mm	0 mm	0 mm	0 mm
Weight, approx.	0.32 kg	0.5 kg	0.8 kg	2.4 kg
Product feature of the enclosure housing for side-by-side mounting	Yes	Yes	Yes	Yes
Installation	Snaps onto DIN rail EN 60715 35x7.5/15	Snaps onto DIN rail EN 60715 35x7.5/15	Snaps onto DIN rail EN 60715 35x7.5/15	Snaps onto DIN rail EN 60715 35x7.5/15
Electrical accessories	Buffer module	Buffer module	Buffer module	Buffer module
Mechanical accessories				Device identification label 20 mm × 7 mm, pale turquoise 3RT1900-1SB20
MTBF at 40 °C	1 804 044 h	1 998 441 h	1 614 510 h	1 778 916 h
Other information	Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)	Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)	Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)	Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)

附件

SITOP PSE202U 冗余模块	6EP1961-3BA21
输入/输出：24 V DC/40 A 适用于将最大输出电流为 20 A 的两个 SITOP 电源分离
SITOP PSE202U 冗余模块	6EP1962-2BA00
输入/输出：24 V DC/NEC Class 2 适合将两个 SITOP 电源分离，输出功率限于 < 100 VA
SITOP PSE202U 冗余模块	6EP1964-2BA00
输入/输出：24 V DC/10 A 适用于将最大输出电流为 5 A 的两个 SITOP 电源分离
SITOP PSE200U 3 A 选择性模块
4 通道选择性模块输入：24 VDC 输出：24 V DC/3A 每个通道输出电流可调 (0.5 - 3 A)
不带单通道信号	6EP1961-2BA11
带单通道信号	6EP1961-2BA31
SITOP PSE200U 10 A 选择性模块
4 通道选择性模块输入：24 VDC 输出：24 V DC/10 A 每个通道输出电流可调 (3...10 A
不带单通道信号	6EP1961-2BA21
带单通道信号	6EP1961-2BA41
SITOP PSE201U 缓冲模块	6EP1961-3BA01
适用于 SITOP smart 和 SITOP modular 缓冲时间 100 ms 至 10 s 取决于负载电流